baxter Flo-Gard 6301 Скачать руководство пользователя страница 40

Страница: 40 / 252

Modifying the Configuration Option Settings

5-4

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

07-19-B1-729

11. Flow Check: Determines whether the flow check display appears

during device operation, or only when the decimal point key and

TOT

VOL/STATUS

keys are pressed simultaneously.

1: OFF

2: ON

OFF

12. Baud Rate: Determines the baud rate for normal communications

between the pump and a computer. The baud rate is 9600 when the

pump is in modify configuration mode.

1: 300

2: 1200

3: 2400

4: 4800

5: 9600

9600

13. Computer Control: Determines the type of computer control option

available at power up.

1: Disabled

2: Off with Alarm. The pump

drops out of remote control

when an alarm occurs.

3: On with Alarm. The pump

remains in remote control

when an alarm occurs. See

the Programmer’s Manual

2M8963C for additional

information.

Disabled

14. Hospital Area Designator: Determines the hospital area designator

to be displayed upon power ON for 3 seconds. These messages can be

redefined using the computer communications feature.

0: no message

1: NICU

2: PICU

3: MED/SURGICAL

4: TRAUMA/BURN UNIT

5: OPER ROOM

6: CARDIAC/ICU

7: SURGICAL/ICU

8: ICU

9: ONCOLOGY

15. Close Clamp: Determines whether or not the CLOSE CLAMP

message appears with the DOOR OPEN message.

1: OFF

2: ON

16. Insert Clamp: Determines whether or not the slide clamp loading

feature is enabled. The spring retainer must be removed when this

feature is enabled. See “Spring Retainer Removal” on page 8-22 and

“Spring Retainer Installation” on page 8-22.

Note:

The alert or alarm option is available only on pumps running

software versions 1.09 or later.

1: OFF (The spring retainer

should be installed.)

2: ON for software versions

earlier than 1.09 or ALERT

for software versions 1.09 or

later (An audible alert occurs

and the message INSERT

SLIDECLAMP is displayed.

The pump continues

pumping.

3: ALARM (An audible

alarm occurs and the

message INSERT

SLIDECLAMP is displayed.

The pump does not operate.)

ALARM

Table 5-1

Configurable Settings — continued

Parameter Description

Setting Options

Factory

Settings

Содержание Flo-Gard 6301





























































































































































































































































Результаты поиска

Содержание Flo-Gard 6301

Отзывы:

baxter Flo-Gard 6301, Руководство по обслуживанию, Страница: 40 / 252

Результаты поиска

Содержание Flo-Gard 6301

Отзывы: