baxter Flo-Gard 6301 Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 252

baxter Flo-Gard 6301 Скачать руководство пользователя страница 116

9

Air Sensor Calibration

9-6

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

07-19-B1-729

Q

If damage to the slide clamp mechanism or door assembly is seen,
replace as required and retest.

Q

If the safety clamp gap cannot be calibrated, replace the slide clamp
mechanism or the door assembly as required.

Air Sensor Calibration

Note:

This section must be performed when the pump head, CPU board, air sensor,
door/door assembly, door latch, or latch pin is replaced.

1.

Verify if a modification to the pump head door is necessary to complete
this calibration procedure. Open the door and check for a white tubing
guide shim or a letter “A” on the door, opposite the air sensor.

Q

If the shim or letter “A” is present, the modification was already
performed. Proceed to step 2 below.

Q

If the white tubing guide shim or letter “A” is not present, go to
“Tube Guide Shim Installation” on page 8-30 to install the tubing
guide shim. For FLO-GARD 6301 pumps with serial numbers less
than 83030018 but not ending in FA, a modification to the air sensor
assembly is also necessary. Replace the existing air sensor assembly
with a new assembly, part no. F049120023.

2.

Modify an administration set by cutting the tubing about 6 inches below
the first Y-site and splicing in a piece of calibration tubing (part no.
3-2-92-479) using tubing connectors. Fully prime the set with distilled
water.

Note:

This fluid filled tube, along with a dry calibration tubing segment, is used to
calibrate the pump. These sections of tubing should only be used to calibrate
5 pumps with the tubing moved to an unused section for each pump tested.
After the calibration of the fifth pump, discard the segments and replace them
with new ones.

3.

Place the pump upright. If the case is not already opened, separate the
front and rear housings (see “Separation of Front and Rear Housings” on
page 8-5), but do not remove any connectors. Plug the pump into AC
power.

4.

Set the pump to Test Mode 2.

! WARNING !

When working on an open pump, an electrical hazard exists when the pump is
plugged into AC power.

«
...
114
115
116
117
118
...
»

Содержание Flo-Gard 6301





























































































































































































































































Отзывы:

Нет отзывов