baxter Flo-Gard 6301 Скачать руководство пользователя страница 32

Страница: 32 / 252

Charging the Batteries

3-2

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

07-19-B1-729

Functional Test 1

•

Keypad test and Panel Lock switch test

•

Nurse call test

•

DC voltage measurement test

•

Main speaker test

•

Back-up beeper test

•

Calibration constants checked

Final Accuracy Test

•

Pump was tested at 125 mL/hr and 10 mL/hr

•

KVO test

Upstream/Downstream Pressure and Air in Line Test

•

Downstream occlusion

•

Upstream occlusion

•

Air alarm inspection

•

AIL sensor value with empty tube

•

AIL sensor value with primed tube

•

AIL with back pressure service code check

•

Air alarm test

Functional Test 2

•

Free flow prevention

•

Door open/closed inspection

•

FSR and air sensor inspection

•

Drive defect inspection

•

Electrical safety tests

•

Factory setting verification

Final Run-In Test

•

Pump runs at 500 mL/hr for 6 hours and 999 mL/hr for 6 hours

Charging the Batteries

To charge the batteries, plug the pump into a hospital-grade AC outlet. Verify
that the Plug icon lights.

Testing New and Recently Serviced Pumps

Before placing new and recently serviced pumps into service at your facility,
perform the following tests:

! WARNING !

If the charging state of the batteries is unknown or the pump has not been
plugged in to AC power for at least 16 uninterrupted hours then the pump must
be charged for at least 16 uninterrupted hours of charging prior to releasing it
for use.

Содержание Flo-Gard 6301





























































































































































































































































Результаты поиска

Содержание Flo-Gard 6301

Отзывы:

baxter Flo-Gard 6301, Руководство по обслуживанию, Страница: 32 / 252

Результаты поиска

Содержание Flo-Gard 6301

Отзывы: