baxter Flo-Gard 6301 Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 252

baxter Flo-Gard 6301 Скачать руководство пользователя страница 105

07-19-B1-729

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

8-31

Removal/Replacement Procedures

Disassembly/Reassembly

Figure 8-3 Adhesive Application

6.

Immediately place the shim back onto the tube guide using the tape as a
handling aid. Apply finger pressure to the corner of the shim at a 45°
angle as indicated in Figure 8-4. Apply pressure at the ends, as well as, at
the middle of the shim. The tape acts as a barrier preventing adhesive
from contacting the fingers.

Figure 8-4 Pressure Application Points

7.

Hold the shim motionless for 60 seconds while continuing to apply
pressure.

8.

Remove the tape and visually inspect the shim for excess adhesive.
Remove excess adhesive using a dry cotton swab.

9.

Ensure that the shim is properly bonded to the door by verifying that
there are no gaps between the shim and the tubing guide. Use a fingernail
to attempt to lift each end and the middle section of the shim to verify
that the bond is secure.

10.

Perform the Operational Checkout in Chapter 10, “Operational
Checkout”.

Apply Pressure

On Corner

Apply Pressure

On Corner

«
...
103
104
105
106
107
...
»

Содержание Flo-Gard 6301





























































































































































































































































Отзывы:

Нет отзывов