baxter Flo-Gard 6301 Скачать руководство пользователя страница 68

Страница: 68 / 252

Troubleshooting Chart

7-22

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

07-19-B1-729

The audible alarm volume is not loud

enough.

N/A

Turn the VOLUME knob on the rear

of the pump clockwise until the

desired volume is obtained.

Audible alarm is always on.

Momentarily disconnect and

reconnect battery.
Check F302 or F15 (ICP301). Check

CN302, CN701, CN751, and CNI/F

for proper connection and continuity.

Charge or replace battery.
Replace Sensor board.
Replace CPU board.

Audible alarm does not sound.

Turn pump off and back on.

If problem recurs, replace CPU board.
Replace Sensor board.
Replace speaker.

Beep does not sound when a key other

than

BACKLIGHT

SILENCE

pressed when the pump is stopped.

Turn pump off and back on.
Check CN751, CN701, CNI/F1 for

proper connection and continuity.

Repair or replace the connectors.
Replace speaker.
If problem recurs, replace CPU board.
Replace Sensor board.

Optional nurse call is always on.

Check CN401 and CNI/F2 for proper

connection and continuity.

Replace CPU board.
Replace Sensor board.

Optional nurse call is always off.

Verify that the Nurse Call feature has

been enabled via the addition of a

jumper (R421) on the terminal PCB.

Check CN401 and CNI/F2 for proper

connection and continuity.

Replace CPU board.
Replace Sensor board.

Configuration option cannot be set via

the remote computer.

Note:

Computer monitoring and

remote control are available only
when used with user-generated
software applications. See the
FLO-GARD 6301 Programmer’s
Manual for details.

Check the cable connections between

the computer and the pump.
Check that the user-generated

software is properly loaded onto the

computer.
Check CN401 and CNI/F2 for proper

connection and continuity.

Repair connections between computer

and pump.
Restart the program.
Repair or replace connectors as

required.
Replace CPU board.
Replace Sensor board.

Backup buzzer does not activate

during self test.

Check that the buzzer wiring is

connected.
Check for an open fuse on the battery

wire harness.

Plug in connector.
Replace fuse.
Replace backup buzzer.

Table 7-4

Troubleshooting Chart — continued

Symptom

Checks

Corrective Action

Содержание Flo-Gard 6301





























































































































































































































































Результаты поиска

Содержание Flo-Gard 6301

Отзывы:

baxter Flo-Gard 6301, Руководство по обслуживанию, Страница: 68 / 252

Результаты поиска

Содержание Flo-Gard 6301

Отзывы: