manualshive.com logo in svg

baxter Flo-Gard 6301, Руководство по обслуживанию, Страница: 79 / 252

Поделиться
Скачать
baxter Flo-Gard 6301 Скачать руководство пользователя страница 79

07-19-B1-729

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

8-5

Removal/Replacement Procedures

Disassembly/Reassembly

Separation of Front and Rear Housings

1.

Turn the pump off and place it face down on an anti-static mat or work 
surface. Take care not to lay the pump face down on components (such 
as screws) which could damage the front panel.

2.

Remove 10 screws that secure the rear housing to the front housing. 
(Figure 11-4 , items 6 and 40.)

3.

Stand the pump upright and separate the front and rear housings by 
slowly pulling the front half forward by about 10.16 cm (4”).

4.

While the pump is standing, disconnect CN301 and CN302 from the 
CPU board (Figure 11-2 , item 2). The connectors are located at the top, 
in the front half of the pump.

Note: 

The backup audible alarm may be activated. Continue with the following step 
to disable the alarm.

5.

Lay the front case down on its front surface. Position it immediately in 
front of the rear housing.

6.

Disconnect the following connectors so that the halves can be 
completely separated:

6.1

CN751 from the backup audible alarm board (Figure 11-3 , 
item 2) located at the top left of the rear housing to disable the 
backup audible alarm during disassembly.

6.2

Unlock the flat cable connector flange before disconnecting the 
cable by first pulling the flange forward about 2 mm (5/64”).

6.3

Disconnect the flat cable connector CNI/F from the CPU board.

6.4

Disconnect CN1 from the power supply board.

6.5

Disconnect the ground wire from the pump head mounting 
plate for Pump 2 (Figure 11-2 , item 6).

7.

Reassemble the housings in the following order:

7.1

Connect the ground wire to the pump head mounting plate for 
Pump 2.

7.2

Make sure that the connector flange is unlocked and reconnect 
the ribbon cable connector CNI/F on the CPU PCB. Push in the 
flange to hold the ribbon cable in place.

7.3

Reconnect CN1 on the power supply board.

CAUTION

Avoid stressing the pump’s internal cabling when separating the front and rear 
housings.

Содержание Flo-Gard 6301





























































































































































































































































Отзывы:

Нет отзывов