manualshive.com logo in svg

baxter Flo-Gard 6301, Руководство по обслуживанию, Страница: 81 / 252

Поделиться
Скачать
baxter Flo-Gard 6301 Скачать руководство пользователя страница 81

07-19-B1-729

FLO-GARD 6301 DUAL CHANNEL VOLUMETRIC INFUSION PUMP SERVICE MANUAL

8-7

Removal/Replacement Procedures

Disassembly/Reassembly

Separation of Printed Circuit Boards

1.

Separate the front and rear housings completely except for the ground 
wire (“Separation of Front and Rear Housings” on page 8-5).

2.

Disconnect the two connectors (CN601 and CN602) of the front panel 
film (Figure 11-1 , item 3) from the CPU board (Figure 11-2 , item 2).

3.

Disconnect the following pump head connectors (Figure 11-18 ) from 
the CPU board with the wire harness connector extractor, part no. 
UKOG1021.A:

Q

Pump 1: CN201, CN803 (right side) and CN851, CN811 (left side)

Q

Pump 2: CN202, CN852, CN812, and CN804 (left side)

4.

Remove the six screws (Figure 11-2 , item 15) that hold the CPU board 
in the front housing.

5.

Hold the top and bottom center of the CPU board and remove the printed 
circuit boards carefully from the front housing.

Note: 

If resistance is felt, the top portion of the printed circuit boards may be affixed 
to the front housing by the adhesive of the seal around the LCDs. Incline the 
bottom center of the CPU board until the seal comes off the front housing 
before the removal.

6.

Place the printed circuit boards with the LCD display face down on a 
dust free flat surface. Be careful not to touch or damage the LCD display 
surface. Keep them away from dust. Take care not to place the LCD 
display on components (such as screws) that could damage the LCD 
display.

7.

Reassemble in reverse order.

Note: 

Be sure to remove any dirt or dust on the LCD or its windows on the front 
housing before tightening the sensor board to the front housing.

Placing the one side of the CPU board under the two connectors, CN601 and 
CN602, first simplifies the replacement of the board. Do not pinch the pump 
head harness and the grounding wire between the pump head fixing brackets 
(Figure 11-2 , items 5 and 6).

8.

Reconnect all the removed connectors.

9.

Tighten the six screws (Figure 11-2 , item 15) securing the CPU board to 
7 kgf-cm (6.1 in-lb). 

Note: 

The function of the four printed circuit boards can be checked outside of the 
front housing as long as all the connectors are properly connected.

10.

Perform the Operational Checkout procedures in Chapter 10, 
“Operational Checkout”.

Содержание Flo-Gard 6301





























































































































































































































































Отзывы:

Нет отзывов