Avaya P130 SMON Скачать руководство пользователя страница 141

Страница: 141 / 160

Avaya P130 User’s Guide

127

Appendix A

Avaya P130 Embedded Web Manager

The Avaya P130 Embedded Web Manager provides the following:
•

Device Configuration - Viewing and modifying the different device
configurations.

•

Virtual LANs - Viewing and editing Virtual LAN information.

•

Link Aggregation Groups (LAGs) - Viewing and editing LAG information.

•

Software Redundancy - Setting software redundancy for ports in a P130 Switch.

•

Port Mirroring - Setting up port mirroring for ports in a P130 Switch.

•

Trap Managers Configuration - Viewing and modifying the Trap Managers
Table.

•

Switch Connected Addresses - View devices connected to selected ports.

•

IP Multicast filtering with IGMP snooping.

•

Redundancy between LAGs
— Also operates as a result of a module fault, e.g., power failure.

System Requirements

Minimum hardware and Operating System requirements are:
•

Windows® 2000 or NT® 4.0 or higher

•

Pentium® 200-Mhz-based, computer with 64 Mb of RAM

(Pentium-II recommended)

•

Minimum screen resolution of 1024 x 768 pixels

•

Microsoft® Internet Explorer 4 or higher

Netscape Navigator® 4.

or higher

•

Sun Microsystems Java™ plug-in version 1.3.1 (supplied)

Note for users of Netscape Navigator:

The Java plug-in requires certain services from

Windows 95

which are not present if

Internet Explorer

is not installed. In order to

add these services to the operating system, please install Internet Explorer version 3
or higher. You can then use either browser to manage the switch.

Содержание P130 SMON

































































































































































Результаты поиска

Содержание P130 SMON

Отзывы:

Похожие инструкции для P130 SMON

Бренды по названию

Популярные бренды

Avaya P130 SMON, Руководство пользователя

Результаты поиска

Содержание P130 SMON

Отзывы:

Похожие инструкции для P130 SMON

Бренды по названию

Популярные бренды