manualshive.com logo in svg

Avaya P130 SMON, Руководство пользователя, Страница: 42 / 160

Поделиться
Скачать
Avaya P130 SMON Скачать руководство пользователя страница 42

Chapter 4        Installation and Setup

28

 Avaya P130 User’s Guide

5

Set the baud rate, ppp authentication, and ppp time out required to match your 
modem. These commands are described in the “Command Line Interface” 
chapter. 

6

At the prompt, type:

 

set interface ppp enable

 

The CLI responds with the following: 

 

Entering the Modem mode within 60 seconds...

 

Please check that the proprietary modem cable is plugged 
into the console port

7

Use the DB-25 to RJ-45 connector to plug the console cable to the modem’s DB-
25 connector. Plug the other end of the cable RJ-45 connector to the 

 

Avaya P130 console’s RJ-45 port.

8

The Avaya P130 enters modem mode. 

9

You can now dial into the switch from a remote station, and open a Telnet 
session to the PPP interface IP address.

Assigning P130’s IP Stack Address 

Note:  

All P130 switches are shipped with the same default IP address. You must 

change the IP address of the master P130 switch in a stack in order to guarantee that 
the stack has its own unique IP address in the network.

Use the CLI to assign the P130 stack/standalone switch an IP address and net mask. 
The network management station can establish communications with the stack/
standalone switch once this address had been assigned and the stack/standalone 
switch has been inserted into the network.
To assign a P130 IP stack/standalone switch address:
1

Establish a serial connection by connecting a terminal to the Master P130 switch 
of the stack.

2

When prompted for a Login Name, enter the default name

 root

3

When you are prompted for a password, enter the password

 root. 

You are 

now in Supervisor Level.

4

At the prompt, type:

 

set interface inband 

<vlan> <ip_address> <netmask>

 

Replace 

<vlan>

,

 <ip_address>

 and

 

<netmask>

 

with the VLAN, 

 

IP address and net mask of the stack.

5

Press Enter to save the IP address and net mask.

6

At the prompt, type 

reset

 and press Enter to reset the stack. After the Reset, 

log in again as described above.

7

At the prompt, type

 set ip route 

<dest> <gateway>

 

and replace 

<dest>

 

and 

<gateway>

 

with the destination and gateway IP addresses.

Press Enter to save the destination and gateway IP addresses.

Содержание P130 SMON

































































































































































Отзывы:

Нет отзывов