Avaya P130 SMON Скачать руководство пользователя страница 84

Страница: 84 / 160

Chapter 6 Avaya P130 CLI

Avaya P130 User’s Guide

Example:

To display LAG information data for port 10 on module 1:

P130-N> show port channel 1/10 info
Port Speed Duplex Vlan Port Trunk Vlan

   Priority  status Binding
------ ------ ------- ----- --------- -------- --------
1/10 10 half 1 0   off all
1/11 10 half 1 0   off all

Show port mirror Command

Use the

show port mirror

command to display mirroring information for the

switch.

The syntax for this command is:

show port mirror

[<mod_num>[/<port_num>]]

Example:

P130-N> show port mirror
port mirroring
Mirroring both Rx and Tx packets from port 1/2 to port 1/4 is
enabled

Set port level Command

Use the

set port level

command to set the priority level of a port or range of

ports on the switching bus. Packets traveling through a port set at normal priority
should be served only

after

packets traveling through a port set at high priority are

served. Packets traveling with a 802.1p priority header are not affected by this
command.

The syntax for this command is:

set port level

<mod_num>/<port_num> {[0-7]}

mod_num

Module number

port_num

Number of the port on the module

mod_num

Module number

port_num

Number of the port on the module

Содержание P130 SMON

































































































































































Результаты поиска

Содержание P130 SMON

Отзывы:

Похожие инструкции для P130 SMON

Бренды по названию

Популярные бренды

Avaya P130 SMON, Руководство пользователя

Результаты поиска

Содержание P130 SMON

Отзывы:

Похожие инструкции для P130 SMON

Бренды по названию

Популярные бренды