Avaya P130 SMON Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 160

background image

Chapter 6 Avaya P130 CLI

Avaya P130 User’s Guide

103

Set ppp incoming timeout Command

Use the

set ppp incoming timeout

command to configure the number of

minutes until the system automatically disconnects an idle PPP incoming session.

The syntax for this command is:

set ppp incoming timeout

<timeout-in-minutes>

Example:

P130-1# set ppp incoming timeout 20
PPP incoming sessions will automatically disconnect after 20
minutes of idle time.

Show ppp configuration Command

Use the

show ppp configuration

command to view the ppp configuration.

The syntax for this command is:

show ppp configuration

Example:

P130-N> show ppp configuration
PPP baud rate is 38400
PPP incoming timeout is 0 minutes
PPP Authentication Parameters:
------------------------------
Incoming: PAP

<timeout-in-minutes>

Number of minutes between 0 to 999 until the system
automatically disconnects an idle PPP session.
Setting the value to 0 disables the automatic
disconnection of idle sessions. The default is no
timeout.

«
...
115
116
117
118
119
...
»

Содержание P130 SMON

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P130 SMON

Бренд: Brocade Communications Systems Страницы: 60

Бренд: BrainMaster Страницы: 14

CLUSTER SUITE FOR ENTERPRISE LINUX 5.1

Бренд: Red Hat Страницы: 160

ANTI-VIRUS 2011 - REV 2011.11

Бренд: AVG Страницы: 209

Бренд: AppsDaily Страницы: 38

Бренд: Juniper Страницы: 14

Бренд: noveltech Страницы: 13

ITANIUM ARCHITECTURE - SOFTWARE DEVELOPERS VOLUME 3 REV 2.3

Бренд: Intel Страницы: 1898

25366 - Camera Control Pro

Бренд: Nikon Страницы: 94

225A1-05A111-1001 - AutoCAD Electrical 2009

Бренд: Autodesk Страницы: 255

ENTERPRISE LINUX AS 2.1 -

Бренд: Red Hat Страницы: 210

ENTERPRISE LINUX 5.3 - RELEASE MANIFEST

Бренд: Red Hat Страницы: 240

Бренд: FieldServer Страницы: 8

Бренд: Zennio Страницы: 15

Бренд: Datavideo Страницы: 15

WorkForce Pro WP-4015 DN

Бренд: Epson Страницы: 15

Бренд: Epson Страницы: 4

Бренд: NEC Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды