Avaya P130 SMON Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 160

background image

Chapter 6 Avaya P130 CLI

Avaya P130 User’s Guide

73

Set port speed Command

Use the

set port speed

command to configure the speed of a port or range of

ports.
In autonegotiation mode, the port's speed is determined by autonegotiation. You
cannot set the speed type to 10 or 100 when autonegotiation is enabled.

The syntax for this command is:

set port speed <

mod_num/port_num><speed

>

Example:

To configure port 2 on module 1 port speed to 10 Mbps:

P130-1# set port speed 1/2 10MB
Port 1/2 speed set to 10 Mbps.

Set port duplex Command

Use the

set port duplex

command to configure the duplex type of an Ethernet

or Fast Ethernet port or range of ports.
You can configure Ethernet and Fast Ethernet interfaces to either full duplex or half
duplex. The duplex status of a port in autonegotiation mode is determined by
autonegotiation. An error message is generated if you attempt to set the
transmission type of autonegotiation Fast Ethernet ports to half- or full-duplex
mode.

The syntax for this command is:

set port duplex

<mod_num/port_num> {full | half

}

mod_num

Module number

port_num

Number of the port on the module

<speed>

Set port speed to 10, or 100 Mbps

mod_num

Module number

port_num

Number of the port on the module

full

Keyword to specify full-duplex transmission

half

Keyword to specify half-duplex transmission

«
...
85
86
87
88
89
...
»

Содержание P130 SMON

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P130 SMON

LINUX ENTERPRISE DESKTOP 10 SP1 - GNOME 23-05-2007

Бренд: Novell Страницы: 280

Бренд: American DJ Страницы: 21

Бренд: ICP Страницы: 16

WISE INSTALLATION EXPRESS 7.0 SP2

Бренд: Symantec Страницы: 50

Бренд: Teltone Страницы: 65

DSR Series DSR1021

Бренд: Avocent Страницы: 2

Бренд: Agilent Technologies Страницы: 9

ANTI-VIRUS 2011 - REV 2011.11

Бренд: AVG Страницы: 209

Бренд: EEG Страницы: 16

Voyager Digital Media Player

Бренд: BT Страницы: 30

ANTI-VIRUS FOR MICROSOFT EXCHANGE 9.00

Бренд: F-SECURE Страницы: 174

Бренд: Genius Страницы: 3

Бренд: Genius Страницы: 2

VIDEOCAM SLIM USB2

Бренд: Genius Страницы: 4

Бренд: Genius Страницы: 11

Enterprise Manager

Бренд: Oracle Страницы: 38

FINAL MIX VST - FOR TRACKTION

Бренд: Mackie Страницы: 26

COLDFUSION 4.5- TO CFML

Бренд: MACROMEDIA Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды