Avaya P130 SMON Скачать руководство пользователя страница 129

Страница: 129 / 160

Chapter 6 Avaya P130 CLI

Avaya P130 User’s Guide

115

To clear the community string defined for read-only access:

P130-1# set snmp community read-only
SNMP read-only community string cleared.

Set snmp retries Command

Use the

set snmp retries

command to set the number of retries initiated by the

Device Manager application when it tries to send SNMP messages to the device.

The syntax for this command is:

set snmp retries

Example:

P130-1# set snmp retries

Set snmp timeout Command

Use the

set snmp timeout

command to set the SNMP timeout in seconds. This

command is useful for access using the Device Manager.

The syntax for this command is:

set snmp timeout

Example:

P130-1# set snmp timeout 2000

Set snmp trap auth Command

Use the

set snmp trap auth

commands to enable/disable the sending of SNMP

traps upon SNMP authentication failure.

The syntax for this command is:

set snmp trap

{enable|disable}

auth

Example:

P130-1# set snmp trap enable auth
Authentication trap enabled

Number of retries

Time in seconds

Содержание P130 SMON

































































































































































Результаты поиска

Содержание P130 SMON

Отзывы:

Похожие инструкции для P130 SMON

Бренды по названию

Популярные бренды

Avaya P130 SMON, Руководство пользователя

Результаты поиска

Содержание P130 SMON

Отзывы:

Похожие инструкции для P130 SMON

Бренды по названию

Популярные бренды