Avaya P130 SMON Скачать руководство пользователя страница 149

Страница: 149 / 160

Appendix B Specifications

Avaya P130 User’s Guide

135

EMC Emissions

Emissions

Approved according to:
•

US -FCC Part 15 sub part B, class A

•

Europe - EN55022 class A & EN61000-3-2

•

Japan - VCCI-A

Immunity

Approved according to:
•

EN55024

•

E 61000-3-3

Avaya Approved SFF/SFP GBIC Transceivers

This SFF/SFP GBIC (Gigabit Interface Converter) has been tested for use with
Avaya’s P133G2 Gbit/s Gigabit Ethernet ports.

Note:

SFF/SFP GBIC transceivers are hot-swappable.

Safety Information

The SFF/SFP GBIC transceivers are Class 1 Laser products. They comply with

EN 60825-1 and Food and Drug Administration (FDA) 21 CFR 1040.10 and 1040.11.
The SFF/SFP GBIC transceivers must be operated under recommended operating
conditions.

Laser Classification

Note:

Class 1 lasers are inherently safe under reasonably foreseeable conditions of

operation.

CLASS 1

LASER PRODUCT

Содержание P130 SMON

































































































































































Результаты поиска

Содержание P130 SMON

Отзывы:

Похожие инструкции для P130 SMON

Бренды по названию

Популярные бренды

Avaya P130 SMON, Руководство пользователя

Результаты поиска

Содержание P130 SMON

Отзывы:

Похожие инструкции для P130 SMON

Бренды по названию

Популярные бренды