Avaya P130 SMON Скачать руководство пользователя страница 115

Страница: 115 / 160

Chapter 6 Avaya P130 CLI

Avaya P130 User’s Guide

101

Show ppp authentication Command

Use the

show ppp authentication

command to display the authentication

method used for PPP sessions. The shared chap-secret will be displayed only when
accessed from the Technician level.

The syntax for this command is:

show ppp authentication

Example:

P130-N> show ppp authentication

PPP Authentication Parameters:
-----------------------------------------
Incoming: CHAP

P130-N> show ppp authentication

PPP Authentication Parameters:
-----------------------------------------
Incoming: CHAP
CHAP secret: sodot

Set ppp authentication incoming Command

Use the

set ppp authentication incoming

command to define which

authentication method will be used separately when doing a PPP server or client
session.

The syntax for this command is:

set ppp authentication

incoming

{

pap

chap

none

}

incoming

Keyword for setting the authentication method used
in PPP dial-in sessions.

pap

Keyword to use the PAP authentication method.

chap

Keyword to use the CHAP authentication method.

none

Keyword for performing no authentication.

Содержание P130 SMON

































































































































































Результаты поиска

Содержание P130 SMON

Отзывы:

Похожие инструкции для P130 SMON

Бренды по названию

Популярные бренды

Avaya P130 SMON, Руководство пользователя

Результаты поиска

Содержание P130 SMON

Отзывы:

Похожие инструкции для P130 SMON

Бренды по названию

Популярные бренды