background image

Appendix B        Specifications

Avaya P130 User’s Guide

137

Specifications

LX Transceiver

A 9 

µ

m or 10 

µ

m single-mode fiber (SMF) cable may be connected to a 1000Base-LX 

SFF/SFP GBIC port. The maximum length is 10 km (32,808 ft). 
A 50

 µ

m or 62.5 

µ

m multimode (MMF) fiber cable may be connected to a 1000Base-

LX SFF/SFP GBIC port. The maximum length is 550 m (1,804 ft.) for 

 

50 

µ

m and 62.5 

µ

m cable.

The LX transceiver has a Wavelength of 1300 nm, Transmission Rate of 1.25 Gbps,   
Input Power of 3.3V, and Maximum Output Wattage of -3 dBm.

SX Transceiver

A 50

 µ

m

 or 62.5 

µ

m

 multimode (MMF) fiber cable may be connected to a 1000Base-

SX SFF/SFP GBIC port. The maximum length is 500 m (1,640 ft.) for 

 

50 

µ

m

 and 220 m (722 ft.) for 62.5 

µ

m

 cable.

The SX transceiver has a Wavelength of 850 nm, Transmission Rate of 1.25 Gbps,  
Input Power of 3.3V, and Maximum Output Wattage of -4 dBm.

Agency Approval

The transceivers comply with: 

EMC Emission: US – FCC Part 15, Subpart B, Class A; 

 

Europe – EN55022 class A

Immunity: EN50082-1

Safety: UL for US UL 1950 Std., C-UL (UL for Canada) C22.2 No.950 Std., Food and 
Drug Administration (FDA) 21 CFR 1040.10 and 1040.11, and CE for Europe 
EN60950 Std. Complies with EN 60825-1.

Содержание P130 SMON

































































































































































Отзывы: