Avaya P130 SMON Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 160

background image

Chapter 1 Overview

4

Avaya P130 User’s Guide

LAG and Link (Port) Redundancy

Redundancy can be implemented between any two ports in a switch. You can also
assign redundancy between any two LAGs in the switch or between a LAG and a
port.

Spanning Tree

The P130 implements the IEEE 802.1D Spanning Tree (STP) algorithm in order to
allow backup paths and prevent loops throughout the Physical LAN. Spanning Tree
is not available when redundant links are defined.
The P130 supports Spanning Tree per port as well as Spanning Tree per module, as
may be required on the network.

Note:

You cannot configure both Port Redundancy and Spanning Tree on an

individual P130 switch.

Congestion Control

Congestion control is a key element of maintaining network efficiency as it prevents
resource overload.
The P130 supports congestion control on all Ethernet ports, using the following:
•

Head Of Line (HOL) Blocking Prevention

•

IEEE 802.3x Flow Control in full duplex mode.

Advanced Congestion Control (Broadcast storm control)

Limits broadcast, multicast, and unknown packet traffic that traverses the switch.

IP Multicast Filtering (IGMP Snooping)

The IP Multicast Filtering uses the IGMP Snooping protocol to send a single copy of
an IP packet to multiple destinations, and can be used for various applications
including video streaming and video conferencing. This protocol reduces network
congestion and allows more efficient switching of IP multicast traffic (see also the IP
Multicast documentation module).
On Local Area Networks (LANs), IP Multicast packets are transmitted in MAC
Multicast frames. Traditional LAN switches flood these Multicast packets to all
stations in the VLAN. Multicast filtering functions may be added to the Layer 2
switches to avoid sending Multicast packets where they are not required. Layer 2
switches capable of Multicast filtering send the Multicast packets only to ports that
connect members of that Multicast group. This is typically based on IGMP.

«
...
16
17
18
19
20
...
»

Содержание P130 SMON

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P130 SMON

Vantage Pro2 Updater

Бренд: DAVIS Страницы: 12

Quality Monitoring

Бренд: Nortel Страницы: 22

PERFORMANCE MANAGEMENT FOR POWER SYSTEMS

Бренд: IBM Страницы: 12

Бренд: Mitsubishi Electric Страницы: 92

Бренд: Mitsubishi Electric Страницы: 51

Бренд: Mitsubishi Electric Страницы: 57

Бренд: Mitsubishi Electric Страницы: 29

BD DISCRECORDER

Бренд: Ulead Страницы: 18

VB Directory System

Бренд: VBrick Systems Страницы: 21

StreamPlayer v4.4

Бренд: VBrick Systems Страницы: 32

Бренд: FieldServer Страницы: 34

Бренд: Oracle Страницы: 110

Бренд: Bay Networks Страницы: 16

Bay Networks 2000

Бренд: Bay Networks Страницы: 67

Ellisimo Gold II

Бренд: Baby Lock Страницы: 50

COLDFUSION MX 61 - CONFIGURING AND ADMINISTERING COLDFUSION...

Бренд: MACROMEDIA Страницы: 168

System Generator V2.1

Бренд: Xilinx Страницы: 148

EDIRECTORY 8.8 SP1

Бренд: Novell Страницы: 150

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды