Avaya P130 SMON Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 160

background image

Chapter 6 Avaya P130 CLI

Avaya P130 User’s Guide

77

Set port channel Command

Use the

set port channel

command to enable or disable a Link Aggregation

Group (LAG) interface on the module. You can also add or remove a port from an
existing LAG. All ports in the LAG are configured with the base ports' parameters
such as port speed, duplex mode, VLAN ID, tagging mode, priority level. When
adding a port to an existing LAG, type the same LAG-name (or no LAG-name),
otherwise you will get an error message. The added port must belong to the same
connector group - refer to the "LAG" indication on device's front panel. When a port
is removed from a LAG, it becomes disabled.

The syntax for this command is:

set port channel

<mod_num>/<port_list> {on | off} <LAG-name>

Example:

P130-1# set port channel 1/6,18 on server2
Port 1/6 channel mode set to on
Port 1/18 was added to channel

Set port redundancy enable/disable Command

Use the

set port redundancy

command to enable or disable the defined

redundancy schemes. Using this command will not delete existing redundancy
entries.

Note:

You must disable Spanning Tree before you can enable redundancy.

The syntax for this command is:

set port redundancy

{enable|disable}

Example:

P130-1# set port redundancy enable
All redundancy schemes are now enabled

<mod-num>

Module number

<port_list>

A list of ports to be aggregated, separated by commas.

<LAG_name>

Name for the LAG interface.

«
...
89
90
91
92
93
...
»

Содержание P130 SMON

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P130 SMON

Бренд: ROUTE 66 Страницы: 28

MultiRack SoundGrid

Бренд: Waves Страницы: 39

Бренд: COMPRO Страницы: 8

Бренд: Juniper Страницы: 9

Бренд: Unibrain Страницы: 77

Traffix Transcend Traffix Manager

Бренд: 3Com Страницы: 186

MOBILE SECURITY 3.1 FOR S60

Бренд: F-SECURE Страницы: 31

Бренд: GRASS VALLEY Страницы: 4

Бренд: Yamaha Страницы: 24

Stereo and Mono Side chain Compressor

Бренд: Mackie Страницы: 28

Бренд: Bacharach Страницы: 12

DEEP FREEZE ENTERPRISE - TREND MICRO OFFICESCAN...

Бренд: FARONICS Страницы: 17

SCAN TO PC DESKTOP 10

Бренд: Xerox Страницы: 4

Бренд: Patton electronics Страницы: 331

Бренд: Canon Страницы: 139

Бренд: Art-Tech Страницы: 68

Бренд: Brother Страницы: 16

Бренд: Brother Страницы: 361

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды