Avaya P130 SMON Скачать руководство пользователя страница 123

Страница: 123 / 160

Chapter 6 Avaya P130 CLI

Avaya P130 User’s Guide

109

Example:

P130-1# rmon alarm 1026 1.3.6.1.2.1.16.1.1.1.5.1026 60 delta
rising-threshold 10000 1054 falling-threshold 10 1054
risingOrFalling amir
alarm 1026 was created successfully

Rmon event Command

Use the

rmon event

command to create an RMON event entry.

The syntax for this command is:

rmon event

description

owner

<owner>

Example:

P130-1# rmon event 1054 logAndTrap description "event for
monitoring amir's computer" owner amir
event 1054 was created successfully

Sets the upper threshold for the alarm entry.

The RMON event entry that will be notified if the upper
threshold is passed.

Sets the lower threshold for the alarm entry.

The RMON event entry that will be notified if the lower
threshold is passed.

The instances in which the alarm will be activated. The
possible parameters are:

Rising, Falling, risingOrfalling.

<owner>

Owner name string

The event index number of this entry.

<type>

The type of the event. The possible parameters are:

trap, log, logAndTrap, none.

A user description of this event

<owner>

Owner name string

Содержание P130 SMON

































































































































































Результаты поиска

Содержание P130 SMON

Отзывы:

Похожие инструкции для P130 SMON

Бренды по названию

Популярные бренды

Avaya P130 SMON, Руководство пользователя

Результаты поиска

Содержание P130 SMON

Отзывы:

Похожие инструкции для P130 SMON

Бренды по названию

Популярные бренды