Avaya P130 SMON Скачать руководство пользователя страница 60

Страница: 60 / 160

Chapter 6 Avaya P130 CLI

Avaya P130 User’s Guide

The syntax for this command is:

set time client

[enable | disable]

Example:

P130-1(super)# set time client enable
Time client mode enable.

P130-1(super)# set time client disable
Time client mode disabled

Set time server Command

Use the set time server

command to set the IP address for the time server.

The syntax for this command is:

set time server

Example:

P130-1(develop)# set time server 1.2.3.4
The Server Ip has been set to 1.2.3.4

Show time parameters Command

Use the

show time parameters

command to display the current settings for all

time related parameters.

The syntax for this command is:

show time parameters

Example:

P130-1(develop)# show time parameters

Client status: Enabled
Current time : 03:43:43 04 JUL 2002 UTC
Timezone set to 'UTC', offset from UTC is 0 hours
Time-Server : 1.2.3.4
Time acquired from Time-Server: 149.49.54.192
Time protocol set to : TIME protocol

Содержание P130 SMON

































































































































































Результаты поиска

Содержание P130 SMON

Отзывы:

Похожие инструкции для P130 SMON

Бренды по названию

Популярные бренды

Avaya P130 SMON, Руководство пользователя

Результаты поиска

Содержание P130 SMON

Отзывы:

Похожие инструкции для P130 SMON

Бренды по названию

Популярные бренды