Avaya P130 SMON Скачать руководство пользователя страница 82

Страница: 82 / 160

Chapter 6 Avaya P130 CLI

Avaya P130 User’s Guide

Show port auto-negotiation-flowcontrol-advertisement Command

Use the

show port auto-negotiation-flowcontrol-advertisement

command to display the flow control advertisement for a Gigabit port used to
perform auto-negotiation.

The syntax for this command is:

show port auto-negotiation-flowcontrol-advertisement

[<mod_num>[/<port_num>]]

Example:

P130-N> show port auto-negotiation-flowcontrol-advertisement
1/2
Port 1/2 advertises asym-tx-only flow control capabilities.

P130-N> show port auto-negotiation-flowcontrol-advertisement
Port 1/1 does not support this feature.
Port 1/2 does not support this feature.
Port 1/3 advertises no flow control capabilities.
etc.

Show port trap Command

Use the

show port trap

command to display information on SNMP generic link

up/down traps sent for a specific port.

The syntax for this command is:

show port trap

[<mod_num>[/<port_num>]]

Example:

P130-N> show port trap 1/1
Port 1/1 up/down trap is disabled

mod_num

Module number

port_num

Number of the port on the module

mod_num

Module number

port_num

Number of the port on the module

Содержание P130 SMON

































































































































































Результаты поиска

Содержание P130 SMON

Отзывы:

Похожие инструкции для P130 SMON

Бренды по названию

Популярные бренды

Avaya P130 SMON, Руководство пользователя

Результаты поиска

Содержание P130 SMON

Отзывы:

Похожие инструкции для P130 SMON

Бренды по названию

Популярные бренды