Avaya P130 SMON Скачать руководство пользователя страница 80

Страница: 80 / 160

Chapter 6 Avaya P130 CLI

Avaya P130 User’s Guide

Port Commands

Show port Command

Use the

show port

command to display port status.

The syntax for this command is:

P130-N>

show port

[mod_num[/port_num]]

Example:

To display the status for port 4 on module 1:

P130-N> show port 1/4

Port Name Status VLAN Level Neg Dup. Spd. Type
---- ----- ------ ----- ------ ----- ---- ------ ------
1/4 NoName disabled 203 normal enable full 100M 100BaseT

Show Port Output Fields:

mod_num

Module number (optional). If you do not specify a
number, the ports on all modules are shown.

port_num

Number of the port on the module (optional). If you
do not specify a number, all the ports on the module
are shown.

Field

Description

Port

Module and port number

Name

Name of the port

Status

Status of the port (connected, faulty, disabled)

VLAN

VLAN ID of the port

Level

Priority level of the port (normal or high)

Neg

The negotiation status of the port (enable, disable)

Duplex

Duplex setting for the port (fdx, hdx)

Speed

Speed setting for the port (10, 100, 1000)

Type

Port type, for example, 10/100BaseTX, GBIC_SX,
GBIC_LX, GBIC_not present, GBIC_unknown, 1000Base-
T

Содержание P130 SMON

































































































































































Результаты поиска

Содержание P130 SMON

Отзывы:

Похожие инструкции для P130 SMON

Бренды по названию

Популярные бренды

Avaya P130 SMON, Руководство пользователя

Результаты поиска

Содержание P130 SMON

Отзывы:

Похожие инструкции для P130 SMON

Бренды по названию

Популярные бренды