Avaya P130 SMON Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 160

Avaya P130 SMON Скачать руководство пользователя страница 102

Chapter 6 Avaya P130 CLI

88

Avaya P130 User’s Guide

Set trunk Command

Use the

set trunk

command to configure the tagging mode.

The syntax for this command is:

set trunk

<mod_num>/<port_num> {off|dot1q}

Example:

P130-1# set trunk 1/19 dot1q
Dot1Q VLAN tagging set on port 1/19.

P130-1# set trunk 1/19 off
No VLAN tagging set on port 1/19.

Clear vlan Command

Use the

clear vlan

command to delete an existing VLAN and return ports from

this VLAN to the default VLAN #1. When you clear a VLAN, all ports assigned to
that VLAN are assigned to the default VLAN #1.

The syntax for this command is:

clear vlan

[VLAN_num]

Example:

This example shows how you can delete an existing VLAN (VLAN 4) from a
management domain:

P130-1# clear vlan 4
This command will assign all ports on VLAN 4 to their default
in the entire management domain

<mod_num>

Module number

<port_num>

Number of the port on the module

off

Forces the port to become a non-tagging port. The port is in the
clear (tagging) mode: it will never send frames as tagged, but it
will correctly interpret received tagged frames.

dot1q

Forces the port to become a 802.1Q tagging port. The port is in
the tagging mode: it will send frames as tagged and will
correctly interpret received untagged frames.

VLAN_num

Number of the VLAN (range is 1 to 4079).

«
...
100
101
102
103
104
...
»

Содержание P130 SMON

































































































































































Отзывы:

Нет отзывов