Avaya P130 SMON Скачать руководство пользователя страница 59

Страница: 59 / 160

Chapter 6 Avaya P130 CLI

Avaya P130 User’s Guide

Set timezone Command

Use the

set timezone

command to assign a timezone name and set the time

difference of your P130 relative to the Coordinated Universal Time (UTC / GMT).
The minutes parameter can only be set to 30.

The syntax for this command is:

set timezone

Example:

P130-1# set timezone GMT -3:30
Timezone set to 'GMT', offset from UTC is -3:30 hours

Clear timezone Command

Use the

clear timezone

command to return the timezone to its default,

Coordinated Universal Time (UTC).

The syntax for this command is:

clear timezone

Example:

P130-1# clear timezone
Timezone name and offset cleared.

Set time protocol Command

Use the

set time protocol

command to set the protocol for use in the system as

either SNTP protocol or time protocol.

The syntax for this command is:

set time protocol

[sntp-protocol|time-protocol]

Example:

P130-1# set time protocol sntp-protocol
The protocol has been set to SNTP protocol

P130-1# set time protocol time-protocol
The protocol has been set to TIME protocol

Set time client Command

Use the

set time client

command to enable or disable the Time Client mode.

Содержание P130 SMON

































































































































































Результаты поиска

Содержание P130 SMON

Отзывы:

Похожие инструкции для P130 SMON

Бренды по названию

Популярные бренды

Avaya P130 SMON, Руководство пользователя

Результаты поиска

Содержание P130 SMON

Отзывы:

Похожие инструкции для P130 SMON

Бренды по названию

Популярные бренды