Avaya P130 SMON Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 160

background image

Chapter 4 Installation and Setup

Avaya P130 User’s Guide

27

Connecting the Console Cable

The Avaya P130 has one serial port on the front panel of the switch for connecting a
terminal, a terminal emulator, or a modem.
The serial port on the front panel is labelled “Console” and has a RJ-45 connector.
Connect the P130 to a terminal or a terminal emulator using the supplied console
cable and the RJ-45 to DB-9 adaptor. To connect a modem, use the supplied cable
and an RJ-45 to DB-25 adaptor.

Note:

The cable and two adaptors can be found in the accessory set, and they are

clearly marked.

Configuring the Terminal Serial Port Parameters

The serial port settings for using a terminal or terminal emulator are as follows:
•

Baud Rate - 9600 bps

•

Data Bits - 8 bits

•

Parity - None

•

Stop Bit - 1

•

Flow Control - None

•

Terminal Emulation - VT-100

Connecting a Modem to the Console Port

A PPP connection with a modem can be established only after the

Avaya P130 is configured with an IP address and net-mask, and the PPP parameters
used in the Avaya P130 are compatible with the modem’s PPP parameters.
1

Connect a terminal to the console port of the Avaya P130 switch as described in
Connecting the Console Cable.

2

When you are prompted for a Login Name, enter the default name

root

.

3

When you are prompted for a password, enter the password

root

.

You are

now in Supervisor Level.

4

At the prompt, type:

set interface ppp <

ip_addr><net-mask>

with an IP address and netmask to be used by the Avaya P130 to connect via its
PPP interface.

Note:

The PPP interface configured with the

set interface ppp

command

must be on a different subnet from the stack inband interface.

«
...
39
40
41
42
43
...
»

Содержание P130 SMON

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для P130 SMON

Lazett Combo SCX-4116

Бренд: Samsung Страницы: 165

ML 1630 - B/W Laser Printer

Бренд: Samsung Страницы: 18

Бренд: UMAX Technologies Страницы: 10

VCENTER CHARGEBACK 1.5 - API

Бренд: VMware Страницы: 150

Бренд: Red Hat Страницы: 198

COLDFUSION STUDIO 4.5-USING COLDFUSION...

Бренд: MACROMEDIA Страницы: 236

Бренд: NAPCO Страницы: 2

Бренд: eCopy Страницы: 266

ConferenceSuite

Бренд: Polycom Страницы: 2

DuraStor 6220SS

Бренд: Adaptec Страницы: 133

Бренд: Adaptec Страницы: 174

6100BD - Phaser Color Laser Printer

Бренд: Xerox Страницы: 56

LogiCORE Endpoint v2.4

Бренд: Xilinx Страницы: 172

SmartST SmartST Professional

Бренд: Navman Страницы: 60

Бренд: Tascam Страницы: 13

Бренд: Euphonix Страницы: 2

ANTI-EXECUTABLE

Бренд: FARONICS Страницы: 2

Бренд: Dymo Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды