Amazone GreenDrill GD200-E Скачать руководство пользователя страница 57

Страница: 57 / 106

GreenDrill control terminal 5.2

GreenDrill BAH0108-0 03.20

6.6

Calibrating the seed rate [kg/ha or grains/m

]

The seed calibration can be terminated at any time by pressing the

button or

button.

The fan cannot be switched on during calibration.

1. Prepare the implement for the calibration test (see section 5.7, page 47).

2. Check that the correct seed metering wheels have been fitted.

3. Fill the seed hopper.

4. Adjust the brush for the seed type (see section 4.1.3, page 33).

5. Call up the "Calibration" submenu using the

buttons.

6. Confirm the selection with the

button.

7. Select the display with the

buttons.

8. Confirm the selection with the

button.

9. Select the display with the

buttons.

10. Confirm the selection with the

button.

11. Enter the working width with the

buttons (e.g., 3.7 m).

12. Confirm the entry with the

button.

13. Select the display with the

buttons.

14. Confirm the selection with the

button.

15. Enter the forward speed with the

buttons

(e.g. 12.5 km/h).

16. Confirm the entry with the

button.

17. Select the desired calibration test with the

buttons



calibration [kg/ha] or



calibration [grains/m

Содержание GreenDrill GD200-E











































































































Результаты поиска

Содержание GreenDrill GD200-E

Отзывы:

Похожие инструкции для GreenDrill GD200-E

Бренды по названию

Популярные бренды

Amazone GreenDrill GD200-E, Руководство по эксплуатации

Результаты поиска

Содержание GreenDrill GD200-E

Отзывы:

Похожие инструкции для GreenDrill GD200-E

Бренды по названию

Популярные бренды