Amazone GreenDrill GD200-E Скачать руководство пользователя страница 38

Страница: 38 / 106

Structure and function

GreenDrill BAH0108-0 03.20

The following maximum values must not be exceeded:

Operating pressure
of the hydraulic system:

max. 210 bar

Oil flow rate
(tractor pump output):

max. 80 l/min.

Higher oil flow rates can
exceed the maximum
permissible fan hydraulic fluid
temperature.

Fan hydraulic fluid
temperature:

max. 80°C

A measurement strip with a
scale shows the fan hydraulic
fluid temperature via the
housing temperature [°C] of
the hydraulic motor.

With increasing temperature
(from 71°C to 110°C), the
scale becomes black.

4.4.3

GreenDrill GD500-D without fan drive

The GreenDrill GD500-D is not equipped with a fan. The air current for the GreenDrill GD500-D is
produced by the fan of the carrying implement.

The fan speed depends on the carrying implement. Set the fan speed as described in the operating
manual for the carrying implement.

Содержание GreenDrill GD200-E











































































































Результаты поиска

Содержание GreenDrill GD200-E

Отзывы:

Бренды по названию

Популярные бренды

Amazone GreenDrill GD200-E, Руководство по эксплуатации

Результаты поиска

Содержание GreenDrill GD200-E

Отзывы:

Бренды по названию

Популярные бренды