manualshive.com logo in svg

Amazone GreenDrill GD200-E, Руководство по эксплуатации

Поделиться
Скачать
Amazone GreenDrill GD200-E Скачать руководство пользователя страница 50

 

 

 

Implement settings before initial operation 

 

 

50

  

GreenDrill  BAH0108-0  03.20

 

5.8.3 

Setting the fan speed on tractors without flow control valve 

 

Close the control valve (1) of the hydraulic control block before 
actuating the tractor control unit to prevent damage when the fan 
over-revs. 

 

  1.  Close the control valve (1) of the GreenDrill. 

 1.1  Turn the control valve (1) of the 

GreenDrill clockwise (-) up to the stop. 

  2.  Run the tractor engine up to operating 

speed. 

  3.  Apply pressure on the control block with the 

control valve (1). 

 3.1  Actuate the tractor control unit. 

 

 

  4.  Set the fan to the required fan speed. 

4.1.  The scale value (2) can be found in the following table.  

Working width 

3.0 m 

6.0 m 

 12.0 m 

 

Scale value 

3 

4 

max. 

Normal seed 

2 

3 

4 

Fine seed 

4.2.  Set the scale value (2) on the control valve (1). 

4.2   Check the spread pattern on the field.  

 4.3  Optimise the spread pattern by adjusting the fan speed. 

 

Содержание GreenDrill GD200-E











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды