Amazone GreenDrill GD200-E Скачать руководство пользователя страница 48

Страница: 48 / 106

Implement settings before initial operation

GreenDrill BAH0108-0 03.20

5.8

Hydraulic fan drive

Before you adjust the fan speed, check the program settings, see



section 7.1.1, page 87



section 7.1.7, page 90



section 7.1.8, page 91

5.8.1

Connecting the hydraulic hose lines to the tractor

The GreenDrill is equipped with a hydraulic
control block with control valve (1).

The following are connected to the hydraulic
control block



2 hydraulic lines to the fan hydraulic motor
and



2 hydraulic hose lines to the tractor.

The hydraulic hose lines are labelled with P
(red) and T (yellow).

Check whether the return flow line (1) marked in
yellow has a sealing plug (2).

Remove the sealing plug (2) and attach the
separately supplied coupling sleeves (3) on the
return flow line.

Содержание GreenDrill GD200-E











































































































Результаты поиска

Содержание GreenDrill GD200-E

Отзывы:

Бренды по названию

Популярные бренды

Amazone GreenDrill GD200-E, Руководство по эксплуатации

Результаты поиска

Содержание GreenDrill GD200-E

Отзывы:

Бренды по названию

Популярные бренды