manualshive.com logo in svg

Amazone GreenDrill GD200-E, Руководство по эксплуатации

Поделиться
Скачать
Amazone GreenDrill GD200-E Скачать руководство пользователя страница 36

 

 

 

Structure and function 

 

 

36

  

GreenDrill  BAH0108-0  03.20

 

4.4 

 Fan 

The fan generates a flow of air that conveys the metered material to the baffle plates. The air current 
becomes stronger with increasing fan speed. 

A strong flow of air is required for optimal distribution of the seed. If the air flow is too strong, the seed 
can be damaged on the baffle plates. If the air flow is too weak, there may be blockage in the seed 
tube hoses.  

The fan is driven either by an electric motor or a hydraulic motor. 

Read the preliminary fan speed from the table. 

The values in the table are reference values 
and depend on the 

 

seed (grain size and weight) 

 

spread rate 

 

working width 

 

working speed.  

 

Working width

 

Seeding with 

coarse seed 

metering 

wheels

 

fine seed 

metering 

wheels

 

3.0 m

 

3000-3100 

1400-2900 

6.0 m

 

3400-3500 

1550-3300 

12.0 m

 

4200-4300 

1650-4000 

 

Fan speed [rpm] 

Set the fan speed to the value from the table and check the spread pattern on the field. Optimise 
the spread pattern by adjusting the fan speed. 

The fan speed does not change when the working speed changes. To ensure that the spread 
pattern does not change during operation, constantly maintain the selected fan speed.

 

 

4.4.1 

Electric fan drive 

If your implement is equipped with the electric fan drive, the control terminal is used to  

 

switch the electric fan drive on and off,  
see section "Control elements", page 52 and  

 

adjust the fan speed,  
see section "Adjusting the fan speed", page 68. 

Содержание GreenDrill GD200-E











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды