Amazone GreenDrill GD200-E Скачать руководство пользователя страница 64

Страница: 64 / 106

GreenDrill control terminal 5.2

GreenDrill BAH0108-0 03.20

6.7.1

Calibration by driving a calibration distance

1. On the field, measure out a calibration distance of exactly

100 m.
Mark the start and end point of the calibration distance.

2. Drive the tractor to the starting position and put the carrying

implement into working position.

3. Select the display with the

buttons.

4. Confirm the selection with the

button.

5. Confirm the display with the

button.

6. Actuate the

button and drive exactly the calibration

distance.

7. Stop after exactly 100 m and press the

button.



Display when the calibration is complete

If no button is pressed, the display switches to the Main menu
after approx. 5 seconds.

Содержание GreenDrill GD200-E











































































































Результаты поиска

Содержание GreenDrill GD200-E

Отзывы:

Похожие инструкции для GreenDrill GD200-E

Бренды по названию

Популярные бренды

Amazone GreenDrill GD200-E, Руководство по эксплуатации

Результаты поиска

Содержание GreenDrill GD200-E

Отзывы:

Похожие инструкции для GreenDrill GD200-E

Бренды по названию

Популярные бренды