Amazone AD 3000 Super Classic Line Скачать руководство пользователя страница 95

Страница: 95 / 198

Coupling and uncoupling the implement

AD 3000 Super BAH0107-0 02.20

WARNING

Risk of energy supply failure between the tractor and the
implement through damaged power lines!

During coupling, check the course of the power lines. The supply
lines



must give slightly without tension, bending or rubbing on all
movements of the connected implement.



Must not chafe against other parts.

DANGER

When the tractor control units are actuated, several hydraulic
cylinders could be operated at the same time depending on the
switch position.

Direct people out of the danger area.

Risk of injury from moving parts.

During operation, the tractor control unit (yellow) is actuated more
frequently than any other tractor control unit. Assign the connections
of the tractor control unit (yellow) to an easily accessible tractor
control unit in the tractor cab.

Due to the extremely compact design, implement parts may damage
the rear window of the tractor when the implement combination is
raised.

Содержание AD 3000 Super Classic Line







































































































































































































Результаты поиска

Содержание AD 3000 Super Classic Line

Отзывы:

Бренды по названию

Популярные бренды

Amazone AD 3000 Super Classic Line, Руководство по эксплуатации

Результаты поиска

Содержание AD 3000 Super Classic Line

Отзывы:

Бренды по названию

Популярные бренды