manualshive.com logo in svg

Amazone AD 3000 Super Classic Line, Руководство по эксплуатации

Поделиться
Скачать
Amazone AD 3000 Super Classic Line Скачать руководство пользователя страница 173

 

 

 

Faults

 

AD 3000 Super  BAH0107-0  02.20

 

173

 

11 

Faults 

 

WARNING 

Danger of crushing, shearing, cutting, being caught or drawn 
in, winding and knocks through: 

 

unintentional lowering of the implement raised using the 
tractor's three-point hydraulic system 

 

unintentional lowering of raised, unsecured implement 
parts 

 

unintentional start-up and rolling away of the tractor-
implement combination. 

Secure the tractor and the implement against unintentional starting 
and rolling away before eliminating faults on the implement. 

Wait for the implement to stop, before entering the implement 
danger area. 

 

 

CAUTION 

Before working on the implement  

 

couple the pack top seed drill  
and the soil tillage implement. 

 

lower the implement combination onto level solid ground 

 

apply the tractor parking brake 

 

switch off the control terminal 

 

switch off the tractor engine 

 

remove the ignition spanner 

 

disconnect the power supply between the tractor and the 
implement. Disconnect the implement plug (e.g. ISOBUS plug). 
 
Risk of accident due to unintentional activation of the metering 
units or other implement components caused by star wheel 
movement or radar pulses.  

 

Содержание AD 3000 Super Classic Line







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды