Amazone AD 3000 Super Classic Line Скачать руководство пользователя страница 138

Страница: 138 / 198

Settings

138

AD 3000 Super BAH0107-0 02.20

Pre-calibrating the implement

11. Pre-calibrate the seed drill. Preturning

creates the same conditions as when
driving on the field later on.

11.1 Raise the star wheel.

11.2. Insert the calibration crank (Fig. 172/1)

into the square tube of the star wheel.

11.3 Turn the star wheel clockwise

(direction shown by the arrow) until the
seed falls out of all seed housings into
the calibration trays.

11.4 Fill the calibration trays twice by

turning the calibration crank (with fine
seed, approx. 200 crank turns will be
enough).

11.5 Empty the calibration trays into the

seed hopper and place them on the
funnel rails again.

Fig. 172

Содержание AD 3000 Super Classic Line







































































































































































































Результаты поиска

Содержание AD 3000 Super Classic Line

Отзывы:

Бренды по названию

Популярные бренды

Amazone AD 3000 Super Classic Line, Руководство по эксплуатации

Результаты поиска

Содержание AD 3000 Super Classic Line

Отзывы:

Бренды по названию

Популярные бренды