manualshive.com logo in svg

Amazone AD 3000 Super Classic Line, Руководство по эксплуатации

Поделиться
Скачать
Amazone AD 3000 Super Classic Line Скачать руководство пользователя страница 139

 

 

 

Settings

 

AD 3000 Super  BAH0107-0  02.20

 

139

 

Calibrating the seed rate 

 12.  Calibrating the seed rate. 

12.1 Turn the star wheel to the right by the 

number of crank turns specified in the 
table (Fig. 48, page 64). 

12.2 Weigh the seed collected in the 

calibration trays. 
The supplied collapsible bucket is 
used to transfer the collected seed. 
The collected seed is weighed in the 
collapsible bucket.  
The collapsible bucket can be 
conveniently hung on a digital scale, 
which is also included in the scope of 
delivery. 

 

 

Fig. 173 

 

Check the scales to ensure the display 
is accurate, taking the container weight 
into consideration. 

 

 

12.3 Calculate the subsequent seeding rate [kg/ha] from the weight of seed collected (see below) 

 

by a factor of 40 (for 1/40 ha) or 

 

by a factor of 10 (for 1/10 ha). 

Calibrating on 1/40 ha: 

Seed rate [kg/ha] 

= 

Calibrated seed rate [kg/ha] x 40 

 

Calibrating on 1/10 ha: 

Seed rate [kg/ha] 

= 

Calibrated seed rate [kg/ha] x 10 

 

 

Example: 

Calibrated seed rate: 3.2 kg auf 1/40 ha 

Seed rate [kg/ha] 

= 

3.2 [kg/ha] x 40 

= 

128 [kg/ha] 

 

 

 

Содержание AD 3000 Super Classic Line







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды