Amazone AD 3000 Super Classic Line Скачать руководство пользователя страница 135

Страница: 135 / 198

Settings

AD 3000 Super BAH0107-0 02.20

135

8.5.5

Agitator shaft support

This setting affects the seeding rate.

Calibrate the seed rate after the adjustment.

Seeding with agitator shaft support

If the linch pin (Fig. 166/1) is inserted in the hole
of the gearbox hollow shaft, the agitator shaft
support is active.

Fig. 166

Seeding without agitator shaft support

If the linch pin is not inserted in the hole of the
gearbox hollow shaft, the agitator shaft support is
inactive.

When parking, insert the linch pin (Fig. 167/1)
into the hole on the auxiliary shaft.

Fig. 167

Содержание AD 3000 Super Classic Line







































































































































































































Результаты поиска

Содержание AD 3000 Super Classic Line

Отзывы:

Бренды по названию

Популярные бренды

Amazone AD 3000 Super Classic Line, Руководство по эксплуатации

Результаты поиска

Содержание AD 3000 Super Classic Line

Отзывы:

Бренды по названию

Популярные бренды