Amazone AD 3000 Super Classic Line Скачать руководство пользователя страница 128

Страница: 128 / 198

Settings

128

AD 3000 Super BAH0107-0 02.20

8. While filling the seed hopper, set the

bottom flap lever (Fig. 150/1) to a
position between 1 and 4.

Always engage the bottom flap lever in the
group of holes and secure it.

Fig. 150

9.Fill the seed hopper



with bagged goods from a supply
vehicle: The loading aid (Fig. 151/1)
makes it easier to fill with bagged
goods.



with a front loader shovel



from BigBags



with a filling auger.

10. Close the seed hopper cover.

11. Fold up the steps

A latch represents the mechanical transport
locking mechanism for the steps. Check the
latch for proper seating, see section 8.1,
page 122.

Fig. 151

Содержание AD 3000 Super Classic Line







































































































































































































Результаты поиска

Содержание AD 3000 Super Classic Line

Отзывы:

Бренды по названию

Популярные бренды

Amazone AD 3000 Super Classic Line, Руководство по эксплуатации

Результаты поиска

Содержание AD 3000 Super Classic Line

Отзывы:

Бренды по названию

Популярные бренды