Amazone AD 3000 Super Classic Line Скачать руководство пользователя страница 152

Страница: 152 / 198

Settings

152

AD 3000 Super BAH0107-0 02.20

8.10.4 Deactivating/activating the roller harrow

8.10.4.1 Deactivating the roller harrow (lifting)

1. Set the implement down on a level surface.

2. Briefly pull on the lever (Fig. 191/1) and

remove the safety pin for the tube (Fig.
191/2).

Fig. 191

3. Swivel the handle (Fig. 192/1) down.

Fig. 192

4. Push the lever (Fig. 193/1) in the direction

shown by the arrow until the clamping plate
(Fig. 193/2) engages.

5. Insert the safety pin for the tube in a free

hole in parking position.

6. Repeat the procedure for the second lever.

Fig. 193

Содержание AD 3000 Super Classic Line







































































































































































































Результаты поиска

Содержание AD 3000 Super Classic Line

Отзывы:

Бренды по названию

Популярные бренды

Amazone AD 3000 Super Classic Line, Руководство по эксплуатации

Результаты поиска

Содержание AD 3000 Super Classic Line

Отзывы:

Бренды по названию

Популярные бренды