Amazone AD 3000 Super Classic Line Скачать руководство пользователя страница 22

Страница: 22 / 198

General Safety Instructions

AD 3000 Super BAH0107-0 02.20

MD 097

Risk of crushing the entire body when standing in
the lifting area of the three-point hitch when the
three-point hydraulic system is being operated!

Causes serious, potentially fatal injuries anywhere on
the body.



It is forbidden to stand in the lifting area of the
three-point hitch when actuating the three-point
hydraulic system.



Actuate the operator controls for the tractor's
three-point hydraulic system:



only from the designated workstation.



under no circumstances if you are in the
lifting area between the tractor and
implement.

MD 102

Danger from intervention in the implement, e.g.
installation, adjusting, troubleshooting, cleaning,
maintaining and repairing, due to the tractor and
the implement being started unintentionally and
rolling away!

These dangers can cause extremely serious and
potentially fatal injuries.



Secure the tractor and the implement against
unintentional start-up and rolling away before
any intervention in the implement.



Depending on the type of intervention, read and
understand the information in the relevant
sections of the operating manual.

Содержание AD 3000 Super Classic Line







































































































































































































Результаты поиска

Содержание AD 3000 Super Classic Line

Отзывы:

Бренды по названию

Популярные бренды

Amazone AD 3000 Super Classic Line, Руководство по эксплуатации

Результаты поиска

Содержание AD 3000 Super Classic Line

Отзывы:

Бренды по названию

Популярные бренды