Amazone AD 3000 Super Classic Line Скачать руководство пользователя страница 20

Страница: 20 / 198

General Safety Instructions

AD 3000 Super BAH0107-0 02.20

MD 083

Danger of arms being drawn in and/or caught by
moving parts involved in the working process!

This hazard can cause extremely serious injuries
resulting in the loss of limbs.

Never open or remove protective devices while the
tractor engine is running with the universal joint
shaft/hydraulic or electronic systems connected.

MD 089

Risk of crushing the entire body due to standing
under suspended loads or raised implement
parts.

Causes serious, potentially fatal injuries anywhere on
the body.



It is forbidden to stand under suspended loads or
raised implement parts.



Maintain an adequate safety distance from any
suspended loads or raised implement parts.



Ensure that all personnel maintain an adequate
safety distance from suspended loads or raised
implement parts.

Содержание AD 3000 Super Classic Line







































































































































































































Результаты поиска

Содержание AD 3000 Super Classic Line

Отзывы:

Бренды по названию

Популярные бренды

Amazone AD 3000 Super Classic Line, Руководство по эксплуатации

Результаты поиска

Содержание AD 3000 Super Classic Line

Отзывы:

Бренды по названию

Популярные бренды