Amazone AD 3000 Super Classic Line Скачать руководство пользователя страница 179

Страница: 179 / 198

Maintenance and repairs

AD 3000 Super BAH0107-0 02.20

179

The pictogram serves as a
reminder never to aim the cleaning
jet of the (hot water) high pressure
cleaner directly on



electrical components



lubrication points and
bearings



the rating plate, warning
symbols, stickers and design
foils.

The components can be damaged.

Fig. 212

When using (hot water) high pressure cleaners, please note:



Observe the safety regulations for working with your cleaning
device.



Observe the legal regulations for handing and disposing of
cleaning agents.



Do not clean any electrical components with high-pressure
cleaners.



Never aim the cleaning jet of the high pressure cleaner directly
on lubrication points and bearings, rating plates, warning signs,
stickers and design foils.



Pay particular attention to the hydraulic hose lines during
cleaning.



Do not exceed a jet pressure of 120 bar.



Always maintain a minimum nozzle distance of 300 mm between
the high-pressure cleaning nozzle and the implement.



Lubricate the implement after cleaning.

12.3.2 Safety when working on the hydraulic system

Only a specialist workshop may perform work on the hydraulic system.

Содержание AD 3000 Super Classic Line







































































































































































































Результаты поиска

Содержание AD 3000 Super Classic Line

Отзывы:

Бренды по названию

Популярные бренды

Amazone AD 3000 Super Classic Line, Руководство по эксплуатации

Результаты поиска

Содержание AD 3000 Super Classic Line

Отзывы:

Бренды по названию

Популярные бренды