Amazone AD 3000 Super Classic Line Скачать руководство пользователя страница 157

Страница: 157 / 198

Settings

AD 3000 Super BAH0107-0 02.20

157

8.14.2 Move the tramline markers to the transport position

1. Lift the track discs hydraulically, if the track

discs are lowered to create a track, refer to
the "Control terminal" operating manual.

2. Apply the parking brake, switch the motor

off and remove the ignition key.

3. Insert the track disc carrier (Fig. 201/1) on

the transport bracket (Fig. 201/2), and
secure with a pin (Fig. 201/3).

4. Secure the pin (Fig. 201/3) with spring cotter

pins (Fig. 201/4).

5. Repeat the setting work on the second track

disc.

Fig. 201

Содержание AD 3000 Super Classic Line







































































































































































































Результаты поиска

Содержание AD 3000 Super Classic Line

Отзывы:

Бренды по названию

Популярные бренды

Amazone AD 3000 Super Classic Line, Руководство по эксплуатации

Результаты поиска

Содержание AD 3000 Super Classic Line

Отзывы:

Бренды по названию

Популярные бренды