Amazone AD 3000 Super Classic Line Скачать руководство пользователя страница 23

Страница: 23 / 198

General Safety Instructions

AD 3000 Super BAH0107-0 02.20

MD 154

Danger of cuts for other road users caused by
transport with unguarded, sharp harrow tines of
the seed harrow!

Causes serious, potentially fatal injuries anywhere on
the body.

Transportation without a correctly fitted road safety
bar is forbidden.

Install the road safety bar provided before starting
transportation.

MD 157

The stability of the solo implement is guaranteed
only if the empty implement is supported on the
parking supports.

Always set the empty implement down so that it is
stable, on a horizontal parking area with a firm base.

Содержание AD 3000 Super Classic Line







































































































































































































Результаты поиска

Содержание AD 3000 Super Classic Line

Отзывы:

Бренды по названию

Популярные бренды

Amazone AD 3000 Super Classic Line, Руководство по эксплуатации

Результаты поиска

Содержание AD 3000 Super Classic Line

Отзывы:

Бренды по названию

Популярные бренды