Altigen ACM 6.7 Скачать руководство пользователя страница 391 | Manualshive

Страница: 391 / 470

background image

Exchange Integration Configuration Steps

MAXCS ACM 6.7 Administration Manual 377

Figure 161. Choosing the

Synchronize

Exchange Integration mode in MAXCS

4. Configure the names of each extension user such that the first and last names are

the same as the user’s matching mailbox on the Exchange Server.

Note:

The

Middle Initial

field should be

empty

for Exchange Server mail accounts

in order for Exchange integration to work properly.

5. MAXCS matches the mailbox on the Exchange Server via the display name, which is

a combination of “FirstName LastName”. In the example in Figure 162, the display
name is “Michael Wang”, so you should make sure the user’s display name on the
Exchange Server is “Michael Wang”, or synchronization will fail.

Figure 162. First name and last name in MAXCS must match the display name in

Exchange Server, or synchronization will fail. (Also, to synchronize MAXCS
voice mail with Exchange voice mail in Bridged Access mode, you must have
checked the

Enable Synchronization

check box in the Voice Mail

configuration screen.)

Note:

Exchange 2007 Native VM integration uses the extension number and the
extension’s first and last names to link between MAXCS and Exchange.

Select the Exchange
Integration mode you
are going to use.

Enter the NAME (not
the IP address) of the
Exchange Server

«
...
389
390
391
392
393
...
»

Содержание ACM 6.7























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACM 6.7

Бренд: Sven Страницы: 12

dmc1 Finish-Out

Бренд: M&S Systems Страницы: 8

Бренд: Yamaha Страницы: 14

Бренд: Yamaha Страницы: 28

Бренд: Yamaha Страницы: 109

Бренд: Yamaha Страницы: 3

Бренд: Zeck Audio Страницы: 16

AQUASNAP 30RA "B"

Бренд: Carrier Страницы: 36

Бренд: Audipack Страницы: 12

Бренд: KAR-TECH Страницы: 55

Бренд: Laser Страницы: 3

Бренд: Magnavox Страницы: 23

Бренд: Rath Страницы: 7

Бренд: ICON Страницы: 6

Бренд: HME Страницы: 2

Бренд: Matrix Telecom Страницы: 98

Бренд: AbleNet Страницы: 8

Бренд: Teac Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды