Altigen ACM 6.7 Скачать руководство пользователя страница 333 | Manualshive

Страница: 333 / 470

background image

Setting VoIP Codec Profiles

MAXCS ACM 6.7 Administration Manual 319

•

User

button displays information about extensions in the VoIP domain and lets you

change an extension to global or local and relocate an extension.

•

Department

button lets you define departments in the VoIP domain and assign

extensions to departments.

•

Global LCR

button lets you add E.164 number patterns and specify source and

target sites.

Tabs Displayed with the

Servers

Button

•

Information

tab displays information about the selected site and lets you configure

a PSTN number for global extension rerouting as a failover when the TCP/IP network
is down. You may also assign an alternate server to which to redirect global AltiGen
IP phones when their primary server is down.

•

IP Networks

tab defines IP networks and the bandwidth information for an MAXCS

site. Bandwidth usage control for Internet and intranet can be set up here. If the
bandwidth usage exceeds the maximum setting, the call will not be established.

•

IP Dialing Table

tab defines the IP dialing table for a MAXCS site. Specified

information here includes a codec profile and a protocol (SIP or H323) for the
communication from this site to the selected site.

•

IP Codec

tab lets you specify an inter-gateway codec and define IP device ranges

to which you can assign a codec profile.

•

Number Plan

tab displays the number plan information that is set up in MaxAdmin,

System Configuration window,

Number Plan

tab.

Changing the Enterprise Manager Password

Only a person with DomainAdmin rights can change the Enterprise Manager password.
To change the password, click the

Password

button at the top of the Enterprise

Manager window.

Enter the old password, and the new password. Confirm the password, and click

OK

.

Setting VoIP Codec Profiles

The codec setting is profile-based. For different IP addresses and protocols, a different
preferred codec can be used. Each codec profile can have its own codec (G.711, G.723,
G.729), packet length, and jitter buffer. The codec profile can be assigned to connectivity
with a remote server, IP phone or other VoIP device.
By default, the following IP address ranges (private IP addresses) will use G.711 codec:

•

192.168.0.0 to 192.168.255.255

•

172.16.0.0 to 172.31.255.255

«
...
331
332
333
334
335
...
»

Содержание ACM 6.7























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACM 6.7

Бренд: Quickie Страницы: 108

Бренд: Nexvoo Страницы: 20

Бренд: B&B Molders Страницы: 18

Бренд: heat-timer Страницы: 40

Бренд: Parker Страницы: 47

Бренд: ZheJiang Libiao Robotics Страницы: 10

Бренд: Daewoo Страницы: 22

Бренд: Landscape Vibrations Страницы: 8

Бренд: N-Com Страницы: 12

Бренд: Crestron Страницы: 26

Бренд: Panasonic Страницы: 8

SCEN15 - DESKTOP CD AUDIO SYS

Бренд: Panasonic Страницы: 8

SCEN33 - CD STEREO SYSTEM

Бренд: Panasonic Страницы: 8

Бренд: PowerBass Страницы: 16

Бренд: Konftel Страницы: 5

Бренд: Konftel Страницы: 31

Бренд: APART Страницы: 24

Бренд: Chatter Box Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды