Altigen ACM 6.7 Скачать руководство пользователя страница 38

Страница: 38 / 470

Minimum System Requirements

MAXCS ACM 6.7 Administration Manual

Boards Supported by ACC and ACM

•

Quantum boards are no longer supported back to the 6.0 release.

•

IP4-Port Boards are no longer supported.

•

Triton T1/PRI Board (1.544M Hz) revision A3 or above

•

Triton T1/E1/PRI Board (2.048M Hz) all revisions

•

Triton IP Boards revision A3 or above, which includes:

•

IP12-Port Board (G.711/G.723.1/G.729A+B)

•

IP 30-Port Board (G.711 Only) (same hardware as 12-Port IP Board)

•

Triton Analog 12-Extension Board Rev A3 or above

•

Triton Analog 12-Trunk LS/GS Board Rev A3 or above

•

Triton Analog 12-Trunk LS Board Rev A3 or above

•

Triton Analog 8 port trunk all revisions

AltiAPI (Alticomlib.dll)

•

Windows 7

•

Windows 2008 Server

•

Windows 2003 Server

•

Windows XP Professional with SP3 or later

MaxInsight Requirements
Operating Systems

•

Windows 7

•

Windows Vista Business Edition

•

Windows XP Professional with SP2 or higher

System

IBM/PC AT compatible system

Processor

1 GHz CPU or faster

Disk Space

1 GB

RAM

1 GB RAM

Notes

Required:

•

SVGA monitor (1024x768) with 256-color
display or better

•

Keyboard and mouse

TAPI Requirements
TAPI Server

•

Windows 2008 R2

•

Windows 2008

•

Windows 2003

•

Windows XP Professional with SP3 or later

TAPI Client (all 32-bit)

•

Windows 7

•

Windows Vista

•

Windows XP Professional with SP3 or later

AltiGen SDK Requirements

Содержание ACM 6.7























































































































































































































































































































































































































































































Результаты поиска

Содержание ACM 6.7

Отзывы:

Похожие инструкции для ACM 6.7

Бренды по названию

Популярные бренды

Altigen ACM 6.7, Руководство администратора

Результаты поиска

Содержание ACM 6.7

Отзывы:

Похожие инструкции для ACM 6.7

Бренды по названию

Популярные бренды