manualshive.com logo in svg

Altigen ACM 6.7, Руководство администратора

Администраторская инструкция для Altigen ACM 6.7 доступна для бесплатного скачивания на manualshive.com. Ищите нужную информацию в нашем подробном руководстве, чтобы управлять программой эффективно. Скачайте руководство сейчас и получите полную информацию для настройки и использования Altigen ACM 6.7.

Поделиться
Скачать
background image

Overview

14

  MAXCS ACM 6.7 Administration Manual

NAT Configuration for SIP/H.323

 - When MAXCS is behind NAT with a private IP 

address, this feature helps to resolve IP address resolution problems when 
communicating with an external VoIP device.

Silence Detection

 and 

Suppression

 - when silence suppression is enabled and silence 

is detected, the system stops sending packets to the other side. The other side does not 
receive any packets and plays silence.

VoIP Hop-Off Call Support

 - allows an extension to access a PSTN trunk on the remote 

system and “hop off” to dial an outside telephone number. This hop off feature can be 
enabled or disabled on the remote system. Outcall restrictions for hop off calls are 
configurable.

SIP Trunk Support

 - MAXCS enables AltiGen’s system to connect to IP-based trunking 

service providers via SIP. 

SIP NAT Traversal

 - Allows MAXCS to connect to a remote SIP phone or IPTalk behind 

NAT without changing the NAT setting at the remote location.

Support for RFC 2833 (DTMF payload embedded with RTP)

 - Supported in SIP 

trunks only. This feature helps to resolve DTMF tone detection and regeneration when 
using G.723.1 or G.729 codec. Basically low bit rate compression will distort DTMF tone 
during compression. The far end device may not be able to recognize the DTMF digits. 
RFC 2833 specifies a separate RTP payload format to carry DTMF information to ensure 
the other side can recognize the tone properly.

Support for both SIP and H.323 Tie Trunk

 - When setting up a system-to-system 

VoIP tie trunk, either SIP or H.323 protocol can be used.

Multi-Site VoIP Management - Enterprise Manager

Multi-site management through Enterprise Manager includes:

VoIP domain 

- when networking multiple AltiGen systems from different sites, one 

system can be assigned as VoIP domain controller to propagate configuration data to 
member systems.

Directory Synchronization

 - when a new extension is added to one of the member 

systems and configured as Global extension, the VoIP domain controller will propagate 
this extension to all member systems. Every member system within the VoIP domain will 
be able to see the extension number plan of other systems.

Multi-site Call Routing

 - when a user dials an extension number that is not a local 

extension number, the system will search the Domain extension list. If a list is found, 
the system will dial the number by using the IP address and extension number stored in 
the Domain extension list.

Domain User Management

 - The VoIP domain controller can resolve the conflict if 

duplicated extension numbers are created in different member systems. This feature 
also manages extension relocation. When an extension user is relocated to another 
member system, its voice mail and greeting can be moved along with it.

Global Least Cost Routing 

- when multiple systems are in different area codes or 

countries, the administrator can set up Global Least Cost Routing to route long distance 
or international calls through member systems. The routing rules are propagated to all 
members automatically.

Global Dial-by-Name and Greeting Synchronization

 - Caller using the dial-by-name 

feature from any system within the VoIP domain can search the entire global directory. 
The global extension’s greeting is replicated to all systems within the VoIP domain. 

Содержание ACM 6.7























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ACM 6.7

Panasonic DVD-CV36 Quick Manual preview
DVD-CV36
Бренд: Panasonic Страницы: 2
Talk-a-Phone ETP-MT/R OP SOLAR Installation Instructions preview
ETP-MT/R OP SOLAR
Бренд: Talk-a-Phone Страницы: 5
Xtrons D10 Instruction Manual preview
D10
Бренд: Xtrons Страницы: 11
Accutrol VTS Installation & Operation Manual preview
VTS
Бренд: Accutrol Страницы: 25
IDEATEC DLC4000 User Manual preview
DLC4000
Бренд: IDEATEC Страницы: 32
S.E.M. Fusion Z-7799 Quick Start Manual preview
Fusion Z-7799
Бренд: S.E.M. Страницы: 6
LOGICDATA DYNAMIC MOTION Configuration Handbook preview
DYNAMIC MOTION
Бренд: LOGICDATA Страницы: 23
Polk Audio DB 402 Owner'S Manual preview
DB 402
Бренд: Polk Audio Страницы: 8
PURE SIROCCO 150 Owner'S Manual preview
SIROCCO 150
Бренд: PURE Страницы: 88
Hyundai HM-5065 Instruction Manual preview
HM-5065
Бренд: Hyundai Страницы: 26
Focal SCALA UTOPIA III EVO User Manual preview
SCALA UTOPIA III EVO
Бренд: Focal Страницы: 52
Polycom CX 200 Quick Start Manual preview
CX 200
Бренд: Polycom Страницы: 4
Close Talk Close Talk Conference System Installation Instructions preview
Close Talk Conference System
Бренд: Close Talk Страницы: 2
Precision Planting 20/20 SeedSense Operator'S Manual preview
20/20 SeedSense
Бренд: Precision Planting Страницы: 65
Prentke Romich Company Accent 1400 User Manual preview
Accent 1400
Бренд: Prentke Romich Company Страницы: 264
Extron electronics CLE-F308 Quick User Manual preview
CLE-F308
Бренд: Extron electronics Страницы: 2
Extron electronics TeamWork Connect 300 Kit Installation Manual preview
TeamWork Connect 300 Kit
Бренд: Extron electronics Страницы: 6
Aritech CS-152 User Manual preview
CS-152
Бренд: Aritech Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды