Allen-Bradley 1756-CNB/E Скачать руководство пользователя страница 105

Страница: 105 / 186

Publication 1756-UM523F-EN-P - December 2006

Maintain and Troubleshoot the System

105

Wait several minutes for the system to try to synchronize. What
do the CNB modules in the primary chassis show?

•

PwQS — Stop. Your system is synchronized.

•

PwDS — Go to step 3.

Use this table to troubleshoot the secondary chassis.

Wait several minutes for the system to try to synchronize. Do the
CNB modules in the primary chassis show PwQS?

•

Yes — Stop. Your system is synchronized.

•

No — Go to Troubleshoot a Failure to Synchronize on
page 105.

Troubleshoot a Failure to
Synchronize

To troubleshoot a failure to synchronize, perform this procedure.

If the SRM module
has a

And a secondary CNB
module

And a secondary controller
has a

Then

Green OK LED
Indicator

Does not show NET ERR

Flashing Red OK light

Clear the major fault of the controller.

It is possible that you have to clear the fault on
both the primary and secondary controllers.

Solid Red OK light

A. Cycle the power to the chassis.

B. If the OK light remains solid red, replace the

controller and flash the controller with the
appropriate revision of firmware.

Solid Green OK light

Go to step 4.

Shows NET ERR

⇒

Check all ControlNet taps, connectors, and
terminators for proper connections.

Red OK LED Indicator

⇒

A. Cycle the power to the chassis.

B. If the OK light of the SRM module remains

solid red, contact your local distributor or
Rockwell Automation representative.

IMPORTANT

•

If the steps in this section do not correct the situation, check the
usage of the CNB modules. See Adjust CPU Usage for a CNB Module
on page 123.

•

If the chassis still doesn't synchronize, try to manually synchronize it.
See Manually Synchronize the Chassis on page 118.

Содержание 1756-CNB/E



























































































































































































Результаты поиска

Содержание 1756-CNB/E

Отзывы:

Похожие инструкции для 1756-CNB/E

Бренды по названию

Популярные бренды

Allen-Bradley 1756-CNB/E, Руководство пользователя

Результаты поиска

Содержание 1756-CNB/E

Отзывы:

Похожие инструкции для 1756-CNB/E

Бренды по названию

Популярные бренды