Allen-Bradley 1756-CNB/E Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 186

background image

Publication 1756-UM523F-EN-P - December 2006

Configure and Program the Controller

97

Schedule a ControlNet
Network

To schedule a ControlNet network:

•

schedule a new network.

•

update the schedule of an existing network.

•

check the keepers.

•

save the project for each controller.

Schedule a New Network

To schedule a new network, perform this procedure.

1.

Turn on the power to each chassis.

2.

Start RSNetworx for ControlNet software.

3.

From the File menu, choose New.

4.

From the Network menu, choose Online.

5.

Select your ControlNet network and choose OK.

6.

Select the Edits Enabled check box.

7.

From the Network menu, choose Properties.

8.

From Network Parameters, type or select these parameters.

9.

Choose OK.

IMPORTANT

Before you schedule a ControlNet network, turn on the power
to both redundant chassis. If you schedule a ControlNet
network while the secondary chassis is off, the keeper
signature of a CNB module may not match its partner, and the
secondary chassis will fail to synchronize.

In this box

Specify

Network Update Time

Repetitive time interval in which data is sent over the ControlNet network

Max Scheduled Address

Greatest node number to use scheduled communications on the network

Max Unscheduled Address

Greatest node number that you will use on the network

Media Redundancy

Channels in use

Network Name

Name for the network

«
...
95
96
97
98
99
...
»

Содержание 1756-CNB/E



























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1756-CNB/E

Бренд: Wavelink Страницы: 69

Бренд: Eaton Страницы: 6

Бренд: Eaton Страницы: 35

Бренд: Eaton Страницы: 18

Бренд: Eaton Страницы: 73

Бренд: Eaton Страницы: 4

Cutler-Hammer IQ DP-4000

Бренд: Eaton Страницы: 87

Бренд: Eaton Страницы: 14

Бренд: Eaton Страницы: 36

Бренд: IBM Страницы: 38

Бренд: National Instruments Страницы: 21

Бренд: National Instruments Страницы: 6

Бренд: National Instruments Страницы: 10

Бренд: National Instruments Страницы: 6

Бренд: olympia electronics Страницы: 10

Бренд: Vag Страницы: 15

HmIP-FAL230-C10

Бренд: HomeMatic Страницы: 42

EtherCAT Compact67 Slim

Бренд: elco Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды