Allen-Bradley 1756-CNB/E Скачать руководство пользователя страница 28

Страница: 28 / 186

Publication 1756-UM523F-EN-P - December 2006

Design the System

Laying Out the System

ControlLogix Redundancy Requirements and Recommendations

C
N
B

E
N
B

I/O Modules

D
N
B

D
H
R
I
O

M
V
I

Other Networks

Remote location for all:

•

I/O

•

DNB, DHRIO, & MVI
communication modules

Assign the lowest node numbers
to nonredundant nodes.

An additional node can be:

•

a second CNB module in the same remote chassis or in a different remote chassis.

•

any other ControlNet device (not required to be keeper capable).

ControlNet network:

•

Set NUT

≤

90 ms

•

Set RPIs

≤

375 ms

•

If multiple ControlNet
networks, set NUTs

≤

specified values.

For unscheduled communication,
use

≤

4 PanelView terminals per

controller.

At least 2 nodes in
addition to the CNBs in
the redundant chassis

Multiple redundant chassis
pairs are OK.

Use separate networks for unscheduled and scheduled
communication.

•

For unscheduled communication (HMI, workstations,
message instructions), use either an EtherNet/IP or a
ControlNet network.

•

For scheduled communications (I/O, produced/consumed
tags), use a ControlNet network.

To connect a computer to the
network via an NAP, use a remote
node.

EtherNet/IP

ControlNet

Unscheduled Communication

Scheduled Communication

Содержание 1756-CNB/E



























































































































































































Результаты поиска

Содержание 1756-CNB/E

Отзывы:

Похожие инструкции для 1756-CNB/E

Бренды по названию

Популярные бренды

Allen-Bradley 1756-CNB/E, Руководство пользователя

Результаты поиска

Содержание 1756-CNB/E

Отзывы:

Похожие инструкции для 1756-CNB/E

Бренды по названию

Популярные бренды